When choosing a cleaner for natural stone surfaces, it’s tempting to look at one number first: the pH. A very low or very high pH must mean a strong cleaner, whereas more of a neutral pH must mean something milder. But it’s not quite that simple.

While pH is useful because it tells us whether a cleaning product is acidic, neutral or alkaline, it doesn’t tell the full story of how that chemical will behave, what it will remove or whether it is right for the surface in front of you. In fact, two cleaners can have the same pH and behave completely differently when used on natural stone. 

The real skill isn’t finding the strongest chemical available. It’s understanding the contamination, the surface and what you actually need the product to do.

What Does the pH of a Cleaner Actually Tell You?

The pH scale tells you how acidic or alkaline a solution is. A pH of around 7 is neutral, numbers below 7 are acidic, and numbers above 7 are alkaline. This information is key when working with stone because certain materials are sensitive to particular types of chemistry.

Marble, limestone and travertine, for example, are calcium-based stones. Acidic products can react with the surface and cause etching. That means a cleaner which is perfectly suitable for another material could cause permanent damage when used on one of these stones.

However, knowing the pH still doesn’t tell you everything you need to know. Thinking of pH as a simple scale where the numbers at either end mean ‘strong’ and the middle means ‘weak’ misses several other factors that determine how a cleaning product performs.

Two Cleaners Can Have the Same pH and Behave Very Differently

This is one of the biggest misconceptions around cleaning chemistry. The pH number is only one piece of information. How a product behaves can also depend on several other factors, and at Stone Care Direct, we tend to look at five things:

  1. The chemistry. What has the product actually been formulated to do?
  1. The concentration. Are we dealing with a concentrated treatment or a solution intended for routine maintenance?
  1. The dwell time. How long is the product in contact with the surface?
  1. The contamination. Are we trying to remove everyday dirt, old coatings, or something completely different?
  1. The surface. What material are we actually cleaning, and is there already a sealer, polish or coating present?

The last point is especially important. A cleaner can work brilliantly on the surface it was designed for and be entirely wrong for another one. That doesn’t make it a bad chemical; it just means it’s the wrong chemical for that particular job. Right chemical. Right surface. Right process. That’s more useful than simply choosing a product because its pH looks powerful.

The Strongest Cleaner isn’t Always the Best Cleaner

We sometimes hear people say: ‘I always use the strongest cleaner I can find’. But stronger doesn’t automatically mean better. In fact, if a chemical smells stronger, burns more, foams more or has an extreme pH, it can actually cause more problems. 

Using a chemistry that’s more aggressive than the job requires can affect sealers and coatings, damage sensitive finishes or attack the surface itself. Instead of solving one cleaning problem, you can create a restoration problem.

Of course, that doesn’t mean stronger specialist cleaners don’t have an important role; they absolutely do. The key is using them when the contamination and surface require that chemistry, not because the product seems more powerful. As we often say: The skill isn’t using the strongest product. The skill is knowing when you DON’T need it.

What Can Happen if You Choose the Wrong Cleaner?

The consequences depend on both the chemical and the material being cleaned. On acid-sensitive stones such as marble, an unsuitable acidic cleaner can cause etching. Instead of simply leaving dirt behind, the chemical can physically alter the finish. A polished surface might develop a dull or cloudy patch. In more noticeable cases, the affected area can feel different from the surrounding stone because the surface itself has changed.

Other products can interfere with existing sealers or topical coatings. A floor that previously had an even finish might start to look patchy or become harder to maintain. Using an overly aggressive cleaner can also make the next job more complicated than the original one. This is why we encourage people to identify both the surface and the problem before deciding what to use. ‘I thought it was safe’ unfortunately tends to come just before ‘How do I fix this?’

When is a pH-Neutral Cleaner Enough?

For everyday maintenance, a good pH-neutral cleaner is often exactly what you need. It’s not weak or pointless, just the right chemistry for the right job. Routine maintenance is about removing everyday dirt and grime without unnecessarily affecting the finish.

Our PH7 Pro Clean is designed for exactly this type of cleaning. Its pH-neutral formulation makes it suitable for maintaining a wide range of hard surfaces, including natural stone. This is particularly important after a floor has been professionally cleaned, polished or sealed. Once the surface is in good condition, the aim should be to maintain it rather than repeatedly subjecting it to heavier treatments that it doesn’t need.

Does that Mean You Should Always Use a Neutral Cleaner?

No, going too far in the other direction and treating pH-neutral cleaning as the answer to everything would create another problem. Sometimes the contamination genuinely requires specialist chemistry. Heavy grease, ingrained dirt, old coatings, grout, and rust can all require very different treatments, and a general cleaner may not be designed to handle the problem.

This is where understanding what you’re trying to remove becomes important. If everyday dirt is the issue, routine maintenance chemistry may be enough. If the surface has a failed coating, a normal cleaner won’t remove it just because you scrub harder. The goal isn’t to use the mildest cleaner possible at all costs, it’s to use the appropriate cleaner.

Start With the Surface, Not the Bottle

Before choosing a cleaning chemical, we recommend establishing exactly what you’re dealing with. Is the surface marble, limestone, granite, slate, porcelain or ceramic? Does it have a polished or textured finish? Has it previously been sealed? Is there a topical coating sitting on the surface? Then consider the contamination.

A generally dirty limestone floor and a porcelain floor with mould and mildew both need cleaning, but they shouldn’t be treated the same way. The same applies when something looks like a stain. Before reaching for stronger chemistry, it helps to know whether the mark is actually contamination. A dull patch on polished limestone, for example, might be etching rather than dirt. More cleaning won’t restore a chemically damaged polish.

Surface identification therefore comes before choosing a product. When you start with the bottle and try to make the product fit the problem, mistakes are more likely.

Choose the Right Chemistry for the Job

The pH number on a cleaning product is useful, but it should never be the only factor you consider. Two products can sit at a similar point on the pH scale and still behave differently because their formulation and intended purpose are different. The contamination, concentration, dwell time and, most importantly, the surface all influence what happens next.

At Stone Care Direct, we supply a range of cleaning products for everything from routine natural stone maintenance to more specialist cleaning and restoration work. But we would never recommend choosing a product simply because it seems to be the strongest option. Remember, right chemical, right surface, right process.

If you are unsure what you’re cleaning or which product is best, speak to us before applying anything. We can help you identify what the job actually needs and point you towards the right treatment before you cause any more damage.

Menu
This website uses cookies to ensure you get the best experience on our website: Find out more.